-- *********************************************************************
-- CISCO-VOICE-AALX-PROFILE-MIB
--
-- May 2003, Yizhong Shen
--
-- Copyright (c) 2003 by cisco Systems, Inc.
-- All rights reserved.
--
-- *********************************************************************CISCO-VOICE-AALX-PROFILE-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,
OBJECT-TYPE,Counter32,Unsigned32,Integer32FROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
TEXTUAL-CONVENTION,TruthValueFROM SNMPv2-TC
ciscoMgmt FROM CISCO-SMI
cmgwIndex,
CCallControlJitterDelayMode FROM CISCO-MEDIA-GATEWAY-MIB
CvcSpeechCoderRate FROM CISCO-VOICE-COMMON-DIAL-CONTROL-MIB;ciscoVoiceAalxProfileMIB MODULE-IDENTITYLAST-UPDATED"200504210000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-voice-gateway@cisco.com"DESCRIPTION"This MIB defines the objects specific to voice
over ATM or voice over IP. Those objects are
related to the following areas:
1. CODEC Negotiation (AAL1/AAL5)
2. AAL2 Profile
3. SVC connection. "REVISION"200504210000Z"DESCRIPTION"Deprecated object cvapCodecConfigVbdPacketPeriod
and cvapCodecConfigJitterNomDelay;
Add new object cvapCodecConfigNewJtrNomDelay."REVISION"200410150000Z"DESCRIPTION"Add an new enum 'profileCustom210 (210)' to
CiscoAal2ProfileNumber."REVISION"200307180000Z"DESCRIPTION"Initial version of this MIB module"::={ ciscoMgmt 323}ciscoVoiceAalxProfileMIBNotifs OBJECTIDENTIFIER::={ ciscoVoiceAalxProfileMIB 0}ciscoVoiceAalxProfileMIBObjects OBJECTIDENTIFIER::={ ciscoVoiceAalxProfileMIB 1}cvapCodecConfig OBJECTIDENTIFIER::={ ciscoVoiceAalxProfileMIBObjects 1}cvapAal2Config OBJECTIDENTIFIER::={ ciscoVoiceAalxProfileMIBObjects 2}cvapSvcConfig OBJECTIDENTIFIER::={ ciscoVoiceAalxProfileMIBObjects 3}cvapSvcStats OBJECTIDENTIFIER::={ ciscoVoiceAalxProfileMIBObjects 4}
-- *********************************************************************
--
-- Textual Conventions
--
-- *********************************************************************CiscoAal2ProfileType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"In VoATM, an AAL2 profile is used for the parameters
of bearer traffic during the call setup between the
call agent and the media gateway.
In AAL2 profile negotiation, some call agents provide
the profile, some do not. If the AAL2 profile in the
call setup is not provided by the call agent, the
gateway can select its own configured AAL2 profiles.
Those AAL2 profiles can be ITU standard AAL2 profiles
or customized AAL2 profiles.
This textual convention defines the profile type which
is either standard profile from ITU or customized
profile.
There are two groups of profile types:
itu - ITU standard profiles
custom - Customized profiles."REFERENCE
"ITU I.366.2
ATM forum af-vtoa-0113.000 "SYNTAXINTEGER{itu (1),custom (2)}CiscoAal2ProfileNumber ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This textual convention defines the profile number.
A profile contains a set of entries, each entry
specifies an encoding format with an UUI (User-to-User
Indicator) range and length.
The profile set defines a mapping that the receiver of an
AAL2 type 1 packet uses to interpret the the packet
contents.
(AAL2 has 3 different packet types : type 1: carry voice,
type 2: not used, type 3: event, alarm.)
In other words, the profile set defines which encoding
format from the profile is being used.
The following are the legitimate combinations of
CiscoAal2ProfileType and CiscoAal2ProfileNumber:
ITU: 1, 2, 3, 7, 8, 12
Custom: 100, 101, 110, 200, 210
"REFERENCE"ITU I.366.2
ATM forum af-vtoa-0113.000
"SYNTAXINTEGER{profileITU1 (1),profileITU2 (2),profileITU3 (3),profileITU7 (7),profileITU8 (8),profileITU12 (12),profileCustom100 (100),
profileCustom101 (101),profileCustom110 (110),profileCustom200 (200),profileCustom210 (210)}CiscoCodecPacketPeriod ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This type defines the packetization period for a
particular CODEC in microseconds.
The packetization period represents the time for the
gateway to collect the data from TDM side before
it sends out the packet."SYNTAXINTEGER{pktPeriod5000us (1),
pktPeriod5500us (2),pktPeriod5785us (3),pktPeriod10000us (4),pktPeriod15000us (5),pktPeriod20000us (6),pktPeriod25000us (7),pktPeriod30000us (8),pktPeriod35000us (9),pktPeriod40000us (10),pktPeriod45000us (11),
pktPeriod50000us (12),pktPeriod55000us (13),pktPeriod60000us (14),pktPeriod65000us (15),pktPeriod70000us (16),pktPeriod75000us (17),pktPeriod80000us (18),pktPeriod85000us (19),pktPeriod90000us (20)}cvapCodecTable OBJECT-TYPE
SYNTAXSEQUENCEOF CvapCodecEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table defines attributes of CODEC negotiation.
These attributes are used for CODEC negotiation of a call
when a call setup request is made by call agent to the
media gateway.
One entry for AAL1 and one entry for AAL5 are created when
a new media gateway is detected by media gateway application.
All entries are deleted when the media gateway is removed
from the system."::={ cvapCodecConfig 1}cvapCodecEntry OBJECT-TYPESYNTAX CvapCodecEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing management information for CODEC
negotiation of the adaptation type for a call in the
media gateway."
INDEX{ cmgwIndex, cvapCodecNegotiationAdaptType }::={ cvapCodecTable 1}
CvapCodecEntry ::=SEQUENCE{
cvapCodecNegotiationAdaptType INTEGER,
cvapCodecNegotiationOption INTEGER}cvapCodecNegotiationAdaptType OBJECT-TYPESYNTAXINTEGER{aal5 (1),aal1 (2)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object specifies the adaptation layer which
supports CODEC negotiation of calls and the order of
CODECs used in negotiation can be configured as
the value of cvapCodecNegotiationOption.
The adaptation types include:
aal5 :VoIP with AAL5 as adaptation layer.
aal1 :VoATM with AAL1 as adaptation layer."::={ cvapCodecEntry 1}cvapCodecNegotiationOption OBJECT-TYPESYNTAXINTEGER{lcoRcdLcl (1),lcoLclRcd (2),rcdLcoLcl (3),rcdLclLco (4),lclLcoRcd (5),lclRcdLco (6)}
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object defines the CODEC negotiation option which
determines the order of CODECs used by a call during CODEC
negotiation.
The possible CODEC negotiation options are as follows:
Lco - local connection options
(from local call agent)
Rcd - remote connection description
(from remote gateway)
Lcl - local CODEC list which is defined in the table,
cvapCodecNegotiationTable.
If the value of this object is lcoRcdLcl(1), then
effectively the preferences are:
1. the first priority is to the local connection options
sent by the local call agent
2. the second priority is to the remote connection
description sent by the remote gateway (or related
call agent)
3. the last priority is to the local CODEC list stored
in local gateway
If the value of this object is lcoLclRcd(2), then
effectively the preferences are:
1. the first priority is to the local connection options
sent by the local call agent
2. the second priority is to the local CODEC list stored
in local gateway.
3. the last priority is to the remote connection
description sent by the remote gateway (or related call
agent)
If the value of this object is rcdLcoLcl(3), then
effectively the preferences are:
1. the first priority is to the remote connection
description sent by the remote gateway (or related
call agent)
2. the second priority is to the local connection options
sent by the local call agent
3. the last priority is to the local CODEC list stored
in local gateway
If the value of this object is rcdLclLco(4), then
effectively the preferences are:
1. the first priority is to the remote connection
description sent by the remote gateway (or related
call agent)
2. the second priority is to the local CODEC list stored
in local gateway
3. the last priority is to the local connection options
sent by the local call agent
If the value of this object is lclLcoRcd(5), then
effectively the preferences are:
1. the first priority is to the local CODEC list stored
in local gateway
2. the second priority is to the local connection options
sent by the local call agent
3. the last priority is to the remote connection
description sent by the remote gateway (or related call
agent)
If the value of this object is lclRcdLco(6), then
effectively the preferences are:
1. the first priority is to the local CODEC list stored
in local gateway
2. the second priority is to the remote connection
description sent by the remote gateway (or related
call agent)
3. the last priority is to the local connection options
sent by the local call agent."DEFVAL{ lcoRcdLcl }::={ cvapCodecEntry 2}cvapCodecConfigTable OBJECT-TYPESYNTAXSEQUENCEOF CvapCodecConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This table contains the attributes whose configuration
depends on CODEC types and adaptation types.
For each adaptation layer, one entry for each CODEC rate
supported by the media gateway is created by the system at
power-up."::={ cvapCodecConfig 2}cvapCodecConfigEntry OBJECT-TYPESYNTAX CvapCodecConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry represents a CODEC rate supported for VoIP or
VoATM with different adaptation layers in the media gateway."INDEX{ cmgwIndex, cvapCodecConfigAdaptType, cvapCodecConfigType }::={ cvapCodecConfigTable 1}
CvapCodecConfigEntry ::=SEQUENCE{
cvapCodecConfigAdaptType INTEGER,
cvapCodecConfigType CvcSpeechCoderRate,
cvapCodecConfigPreference Unsigned32,
cvapCodecConfigVoicePacketPeriod CiscoCodecPacketPeriod,
cvapCodecConfigVbdPacketPeriod CiscoCodecPacketPeriod,
cvapCodecConfigJitterDelayMode CCallControlJitterDelayMode,
cvapCodecConfigJitterMaxDelay Unsigned32,
cvapCodecConfigJitterNomDelay Unsigned32,
cvapCodecConfigJitterMinDelay Unsigned32,
cvapCodecConfigDtmfRelay TruthValue,
cvapCodecConfigPayloadType Unsigned32,
cvapCodecConfigNewJtrNomDelay Unsigned32}cvapCodecConfigAdaptType OBJECT-TYPESYNTAXINTEGER{other (1),aal5 (2),aal1 (3),aal2 (4)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An unique index identifying the adaptation layer
supported by voice applications in the media gateway.
The adaptation types include:
other :Voice over other media.
aal5 :VoIP with AAL5 as adaptation layer.
aal1 :VoATM with AAL1 as adaptation layer.
aal2 :VoATM with AAL2 as adaptation layer."::={ cvapCodecConfigEntry 1}cvapCodecConfigType OBJECT-TYPESYNTAX CvcSpeechCoderRate
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"This object specifies the CODEC rate defined in
CvcSpeechCoderRate."::={ cvapCodecConfigEntry 2}cvapCodecConfigPreference OBJECT-TYPESYNTAXUnsigned32(0..255)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specified the preference configured by the
user for each CODEC. Lower the number, higher the
preference of the CODEC.
If this object is set to 0, the corresponding CODEC will
not be used in CODEC negotiation or in CODEC choose command.
For CODECs having the same preference, the entry with the
lower value of cvapCodecConfigType has higher precedence."::={ cvapCodecConfigEntry 3}
cvapCodecConfigVoicePacketPeriod OBJECT-TYPESYNTAX CiscoCodecPacketPeriod
UNITS"microseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the packetization period for a
particular CODEC in voice application.
The packetization period represents the time for the
media gateway to collect the data from TDM side before
it sends out the packet.
This object is not applicable if cvapCodecConfigAdaptType
is set to 'aal2(4)' since the packetization period for
a CODEC in VoATM with AAL2 depends on the associated
profile."::={ cvapCodecConfigEntry 4}cvapCodecConfigVbdPacketPeriod OBJECT-TYPESYNTAX CiscoCodecPacketPeriod
UNITS"microseconds"MAX-ACCESSread-write
STATUSdeprecatedDESCRIPTION"This object specifies the packetization period for a
particular CODEC in VBD (Voice Band Data) upspeed.
The packetization period represents the time for the
media gateway to collect the data from TDM side before
it sends out the packet.
This object is not applicable if cvapCodecConfigAdaptType
is set to 'aal2(4)' since the packetization period for
a CODEC in VoATM with AAL2 depends on the associated
profile."::={ cvapCodecConfigEntry 5}cvapCodecConfigJitterDelayMode OBJECT-TYPESYNTAX CCallControlJitterDelayMode
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The object specifies the jitter buffer mode applied to
a call connection.
adaptive - means to use cvapCodecConfigNewJtrNomDelay as
the initial jitter buffers size and let the DSP
pick the optimal value of the jitter buffer
size between the range of
cvapCodecConfigJitterMaxDelay and
cvapCodecConfigJitterMinDelay.
fixed - means to use a constant jitter buffer size
which is specified by cvapCodecConfigNewJtrNomDelay.
"DEFVAL{ adaptive }::={ cvapCodecConfigEntry 6}cvapCodecConfigJitterMaxDelay OBJECT-TYPESYNTAXUnsigned32(20..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the maximum jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to adaptive(1),
the DSP will dynamically pick an optimal value of the
jitter buffer size between the range of
cvapCodecConfigJitterMaxDelay and
cvapCodecConfigJitterMinDelay.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
this object is ignored.
The value of cvapCodecConfigJitterMaxDelay needs to be
greater than or equal to the value of
cvapCodecConfigNewJtrNomDelay."::={ cvapCodecConfigEntry 7}cvapCodecConfigJitterNomDelay OBJECT-TYPESYNTAXUnsigned32(5..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUSdeprecatedDESCRIPTION"This object specifies the nominal jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
the jitter buffer is fixed at this value for
the duration of the call.
if cvapCodecConfigJitterDelayMode is set to adaptive(1),
the jitter buffer is initially set to this value.
The value of cvapCodecConfigJitterNomDelay needs to be
greater than or equal to the value of
cvapCodecConfigJitterMinDelay and be smaller than or equal
to the value of cvapCodecConfigJitterMaxDelay."::={ cvapCodecConfigEntry 8}cvapCodecConfigJitterMinDelay OBJECT-TYPESYNTAXUnsigned32(0..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the minimum jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to adaptive(1),
the DSP will dynamically pick an optimal value of the
jitter buffer size between the range of
cvapCodecConfigJitterMaxDelay and
cvapCodecConfigJitterMinDelay.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
this object is ignored.
The value of cvapCodecConfigJitterMinDelay needs to be
smaller than or equal to the value of
cvapCodecConfigNewJtrNomDelay."::={ cvapCodecConfigEntry 9}cvapCodecConfigDtmfRelay OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"When this object is set to 'true', the digits will be
sent as peer-to-peer packet in the bearer.
When this object is set to 'false', the digits will be
sent as regular voice packets in the bearer.
For low complexity CODECS (such as G.711), the preferred
value for this object could be 'false'.
For high complexity CODECS (such as G.729A), the preferred
value for this object should be 'true', otherwise
the digits may not get recognized properly at the remote
end."::={ cvapCodecConfigEntry 10}
cvapCodecConfigPayloadType OBJECT-TYPESYNTAXUnsigned32(0..127)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the payload type of the CODEC in
voice application as specified in RFC1890.
The values (0..95) are static payload type.
The values (96..127) are dynamic payload type and it is
specified dynamically through the control protocol during
call setup.
If more than one CODEC have the same payload type,
the CODEC with the highest preference (the lowest value of
cvapCodecConfigPreference) will be selected."REFERENCE"RFC 1890 - RTP Profile for Audio and Video Conferences
with Minimal Control."::={ cvapCodecConfigEntry 11}cvapCodecConfigNewJtrNomDelay OBJECT-TYPE
SYNTAXUnsigned32(2..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the nominal jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
the jitter buffer is fixed at this value for
the duration of the call.
if cvapCodecConfigJitterDelayMode is set to adaptive(1),
the jitter buffer is initially set to this value.
The value of cvapCodecConfigNewJtrNomDelay needs to be
greater than or equal to the value of
cvapCodecConfigJitterMinDelay and be smaller than or equal
to the value of cvapCodecConfigJitterMaxDelay."::={ cvapCodecConfigEntry 12}cvapSvcConfigTable OBJECT-TYPESYNTAXSEQUENCEOF CvapSvcConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains the SVC (both in AAL1 and AAL2)
configuration which is used for call connection establishment
between the PNNI controller and the media gateway."::={ cvapSvcConfig 1}cvapSvcConfigEntry OBJECT-TYPESYNTAX CvapSvcConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing management information for SVC connection
in the media gateway.
An entry of this table is created when a new media gateway is
detected by media gateway application.
The entry is deleted when the media gateway is removed from
the system."INDEX{ cmgwIndex }::={ cvapSvcConfigTable 1}
CvapSvcConfigEntry ::=SEQUENCE{
cvapSvcAtmQosCellDelay Integer32,
cvapSvcAtmQosCtd Integer32,
cvapSvcAtmQosClr Integer32,
cvapSvcTrfScalingFactor Integer32,
cvapSvcAal2CidNumber Integer32,
cvapSvcAggTrafficClipping TruthValue,
cvapSvcAggLinkState INTEGER,
cvapSvcPartialFillSupported Integer32,
cvapSvcMgcpSelectorByteValue Integer32,
cvapSvcH248SelectorByteValue Integer32,
cvapSvcDelNotifGuardTimer Integer32,
cvapSvcMultiCIDPerSvc TruthValue,
cvapSvcMultiCIDFillTimer Unsigned32,
cvapSvcMultiCIDCACSCR Unsigned32,
cvapSvcMultiCIDCACPCR Unsigned32,
cvapSvcMultiCIDOriginatDelTimer Unsigned32,
cvapSvcMultiCIDTerminatDelTimer Unsigned32,
cvapSvcMultiCIDGlareThreshold Unsigned32}cvapSvcAtmQosCellDelay OBJECT-TYPESYNTAXInteger32(500..20000)UNITS"microseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object identifies end-to-end cell delay
in voice SVC establishment.
It is used to guarantee the quality of the route selected
for a voice SVC.
It is applicable to both AAL1 and AAL2 SVC connection
establishment.
This object is part of the extended quality of services
information element which is sent out during SVC setup."REFERENCE"ATM Forum 'Voice & Telephony over ATM' specifications
af-vtoa-0089.000, af-vtoa-0113.000. "DEFVAL{20000}::={ cvapSvcConfigEntry 1}cvapSvcAtmQosCtd OBJECT-TYPESYNTAXInteger32(20000..150000)UNITS"microseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object identifies end-to-end maximum cell transfer
in voice SVC establishment.
It is used to guarantee the quality of the route
selected for a voice SVC.
It is applicable to both AAL1 and AAL2 SVC connection
establishment.
This value is sent in voice SVC setup
messages in end-to-end transit delay information element
as the object value."REFERENCE"ITU G-Series Recommendations:
G.114 - One-way transmission time. "DEFVAL{150000}::={ cvapSvcConfigEntry 2}cvapSvcAtmQosClr OBJECT-TYPESYNTAXInteger32(4..8)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object identifies maximum Cell Loss Ratio (CLR)
in voice SVC establishment.
It is used to guarantee the quality of the route selected
for a voice SVC.
It is applicable to both AAL1 and AAL2 SVC connection
establishment.
This value is sent in voice SVC setup messages in
extended quality of services information element as
maximum cell loss ratio value."REFERENCE"Bell Core specifications - GR.1110 "DEFVAL{8}::={ cvapSvcConfigEntry 3}cvapSvcTrfScalingFactor OBJECT-TYPESYNTAXInteger32(50..200)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies Traffic Scaling Factor
in computing factored bandwidth which is used in ATM
signaling in voice SVC establishment.
When this value is less than 100 it can be referred as a
`discount factor' and when more than 100 referred as an
`excess factor.
This object is applicable only to VBR SVC connection
establishment.
The traffic scaling is not applicable to AAL2 SVC calls
that require G.711 and clear channel CODECs."DEFVAL{100}::={ cvapSvcConfigEntry 4}cvapSvcAal2CidNumber OBJECT-TYPESYNTAXInteger32(8..255)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the default AAL2 CID (Channel
Identification) number used for AAL2 SVC connections.
0-7 is reserved."REFERENCE"ITU I.363-2 B-ISDN ATM Adaptation layer specification:
Type 2 AAL, September 1997.
"DEFVAL{100}::={ cvapSvcConfigEntry 5}cvapSvcAggTrafficClipping OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object defines the aggregate traffic clipping policy.
This object specifies if the aggregate traffic clipping
policy is applicable to all bearer traffic generated in the
media gateway.
The applicable options are:
'true' - aggregate traffic clipping is enabled, local gateway
traffic management performs aggregate traffic clipping.
'false' - aggregate traffic clipping is disabled, local
gateway traffic management does not perform aggregate
traffic clipping.
This is applicable to only AAL2 SVC voice bearer traffic.
When aggregate traffic clipping is enabled, local gateway
can discard cells which are exceeding local gateway aggregate
SVC bandwidth."DEFVAL{ true }::={ cvapSvcConfigEntry 6}cvapSvcAggLinkState OBJECT-TYPESYNTAXINTEGER{up (1),down (2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object provides the state of the SVC link between PNNI
controller and the media gateway.
When the SVC software module fails to register NSAP address
with the PNNI controller via SAPI (Service Access Point
Interface), this object will be set to 'down', when it
is successful, this object will be set to 'up'.
if down
SVC calls cannot be made on gateway
if up
SVC calls can be made on gateway "::={ cvapSvcConfigEntry 7}cvapSvcPartialFillSupported OBJECT-TYPESYNTAXInteger32(1..48)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object indicates the fill level of cells in case of
AAL1 adaptation .
The value of this object will be used if the call agent does
not specify partial fill in the MGCP commands (i.e if
L(local connection option):pf( partial fill) is absent).
ATM cell size is 53 bytes, 5 bytes for header, 48 bytes
for data. If the data are not enough to fill 48 bytes of one
ATM cell, the system can fill in the value of this object to
the padding bytes."DEFVAL{47}::={ cvapSvcConfigEntry 8}cvapSvcMgcpSelectorByteValue OBJECT-TYPESYNTAXInteger32(1..255)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the selector byte value of the NSAP
address for MGCP protocol.
When a SVC call setup indication from the network is received,
it will look at this object to determine the owner application
for this setup.
The value of this object can not be modified when ATM SVC
calls are up.
The value of this objects can not equal to the value of
'cvapSvcH248SelectorByteValue'."DEFVAL{21}
::={ cvapSvcConfigEntry 9}cvapSvcH248SelectorByteValue OBJECT-TYPESYNTAXInteger32(1..255)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the selector byte value of the NSAP
address for H.248 protocol.
When a SVC call setup indication from the network is received,
it will look at this object to determine the owner application
for this setup.
The value of this object can not be modified when ATM SVC
calls are up.
The value of this objects can not equal to the value of
'cvapSvcMgcpSelectorByteValue'."DEFVAL{20}::={ cvapSvcConfigEntry 10}
cvapSvcDelNotifGuardTimer OBJECT-TYPESYNTAXInteger32(1..120)UNITS"seconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"A timer, for a duration as specified by this object,
will be started when the SVC call is released from the
network side. Upon expiration of this timer, the call
agent is notified about this through ServiceChange
message(for H.248 protocol) or through gateway initiated
delete message(for MGCP protocol).
This object is not applicable for Multi-CID SVC(if MIB object
'cvapSvcMultiCIDPerSvc' is set to 'true')."DEFVAL{60}::={ cvapSvcConfigEntry 11}cvapSvcMultiCIDPerSvc OBJECT-TYPESYNTAXTruthValue
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object enables the user to disable or enable the
Multi-CID SVC feature on the gateway.
When this object is set to 'true', multiple CIDs can be
established on a single SVC. When this object is set to
'false', only one CID per SVC can be established.
This object cannot be modified when active SVC calls exist
on the gateway."REFERENCE"Media gateway AAL2 Bearer-Path Establishment,
draft-barr-megaco-aal2bearer-00-txt, June 2002."DEFVAL{ false }::={ cvapSvcConfigEntry 12}cvapSvcMultiCIDFillTimer OBJECT-TYPESYNTAXUnsigned32(0..255)UNITS"milliseconds"
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object defines the time (millisecs) to wait for filling
up the cell when the next packet is not ready. After waiting
for the time configured in this object, the cell will be sent
out.
This object is applicable only for aal2 adaptations.
Any new programmed value will not affect SVCs already
in progress."DEFVAL{10}::={ cvapSvcConfigEntry 13}cvapSvcMultiCIDCACSCR OBJECT-TYPESYNTAXUnsigned32(20..60000)UNITS"Cells per Second"MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"This object specifies the SCR (Sustained Cell Rate) per
Multi-CID SVC.
The value of this object will be used for CAC (Call Admission
Control) processing, and will determine if a new Multi-Cid SVC
needs to be created for a new incoming CID, or whether there
is room to add the new CID on the Multi-CID SVC."REFERENCE"Media gateway AAL2 Bearer-Path Establishment,
draft-barr-megaco-aal2bearer-00-txt, June 2002,
Section 5.0 paragraph 4."DEFVAL{450}::={ cvapSvcConfigEntry 14}cvapSvcMultiCIDCACPCR OBJECT-TYPESYNTAXUnsigned32(20..60000)UNITS"Cells per Second"MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"This object specifies the PCR (Peak Cell Rate) per Multi-CID
SVC.
The value of this object will be used for CAC (Call Admission
Control) processing, and will determine whether an upspeed
request can be accepted or not on the Multi-CID SVC.
The 'cvapSvcMultiCIDCACPCR' must be greater than or equal to
'cvapSvcMultiCIDCACSCR'."REFERENCE"Media gateway AAL2 Bearer-Path Establishment,
draft-barr-megaco-aal2bearer-00-txt, June 2002,
Section 5.0 paragraph 4."DEFVAL{875}::={ cvapSvcConfigEntry 15}cvapSvcMultiCIDOriginatDelTimer OBJECT-TYPESYNTAXUnsigned32(0..1200)UNITS"seconds"MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"This object specifies the time to wait to delete an Originated
-SVC in the case where a CID delete just occurred and the SVC
has no more CIDs after the deletion.
The interval of this object should be 5.
The 'cvapSvcMultiCIDOriginatDelTimer' must be greater than
or equal to 'cvapSvcMultiCIDTerminatDelTimer+5', except for
the case that 'cvapSvcMultiCIDOriginatDelTimer' is 0 and
'cvapSvcMultiCIDTerminatDelTimer' is 0 (which means that the
Delete Timer feature is disabled)."REFERENCE"Media gateway AAL2 Bearer-Path Establishment,
draft-barr-megaco-aal2bearer-00-txt, June 2002,
Section 5.5."DEFVAL{15}::={ cvapSvcConfigEntry 16}cvapSvcMultiCIDTerminatDelTimer OBJECT-TYPESYNTAXUnsigned32(0..1195)
UNITS"seconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the time that the Terminating end can
attempt to add a new CID into the Terminated-SVC after the
last CID in a slave-end SVC is deleted.
The interval of this object should be 5.
The 'cvapSvcMultiCIDOriginatDelTimer' must be greater than
or equal to 'cvapSvcMultiCIDTerminatDelTimer+5', except for
the case that 'cvapSvcMultiCIDOriginatDelTimer' is 0 and
'cvapSvcMultiCIDTerminatDelTimer' is 0 (which means that the
Delete Timer feature is disabled)."REFERENCE"Media gateway AAL2 Bearer-Path Establishment,
draft-barr-megaco-aal2bearer-00-txt, June 2002,
Section 5.5."DEFVAL{10}::={ cvapSvcConfigEntry 17}cvapSvcMultiCIDGlareThreshold OBJECT-TYPESYNTAXUnsigned32(0..248)
UNITS"number of CIDs"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the threshold at when reached
on the SVC-Terminating end, that no more CID's can
be added to that Terminated-SVC from the Termination
end. The Originating end will be able to use the
remaining CID's in the SVC."REFERENCE"Media gateway AAL2 Bearer-Path Establishment,
draft-barr-megaco-aal2bearer-00-txt, June 2002,
Section 6.3."DEFVAL{243}::={ cvapSvcConfigEntry 18}cvapSvcStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CvapSvcStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains SVC statistics associated with
the communication between the media gateway and the PNNI
controller. "::={ cvapSvcStats 1}cvapSvcStatsEntry OBJECT-TYPESYNTAX CvapSvcStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing statistics information for a SVC
that is associated with the communication between the
media gateway and the PNNI controller."INDEX{ cmgwIndex }::={ cvapSvcStatsTable 1}
CvapSvcStatsEntry ::=SEQUENCE{
cvapSvcTxSetups Counter32,
cvapSvcRxSetups Counter32,
cvapSvcTxCallProcs Counter32,
cvapSvcRxCallProcs Counter32,
cvapSvcTxConns Counter32,
cvapSvcTxConnAcks Counter32,
cvapSvcRxConns Counter32,
cvapSvcRxConnAcks Counter32,
cvapSvcTxReleases Counter32,
cvapSvcTxReleaseCompls Counter32,
cvapSvcRxReleases Counter32,
cvapSvcRxReleaseCompls Counter32,
cvapSvcTxRestarts Counter32,
cvapSvcTxRestartAcks Counter32,
cvapSvcRxRestarts Counter32,
cvapSvcRxRestartAcks Counter32,
cvapSvcTxResyncStrts Counter32,
cvapSvcTxResyncStrtAcks Counter32,
cvapSvcRxResyncStrts Counter32,
cvapSvcRxResyncStrtAcks Counter32,
cvapSvcTxResyncEnds Counter32,
cvapSvcTxResyncEndAcks Counter32,
cvapSvcRxResyncEnds Counter32,
cvapSvcRxResyncEndAcks Counter32,
cvapSvcTxBulkResyncs Counter32,
cvapSvcRxBulkResyncs Counter32,
cvapSvcCallProcExpiries Counter32,
cvapSvcReleasExpiries Counter32,
cvapSvcConnExpiries Counter32,
cvapSvcConnAckExpiries Counter32,
cvapSvcRestartExpiries Counter32,
cvapSvcResyncExpiries Counter32}cvapSvcTxSetups OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'SETUP' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 1}cvapSvcRxSetups OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'SETUP' messages
received by the media gateway from the PNNI
controller since last gateway reset. "::={ cvapSvcStatsEntry 2}cvapSvcTxCallProcs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'PROCEED' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 3}cvapSvcRxCallProcs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'PROCEED' messages
received by the media gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 4}cvapSvcTxConns OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'CONNECT' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 5}cvapSvcTxConnAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'CONNECT ACK' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "
::={ cvapSvcStatsEntry 6}cvapSvcRxConns OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'CONNECT' messages
received by the media gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 7}cvapSvcRxConnAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'CONNECT ACK' messages
received by the gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 8}
cvapSvcTxReleases OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RELEASE' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 9}cvapSvcTxReleaseCompls OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RELEASE COMPLETE'
messages sent to the PNNI controller from the media
gateway since last gateway reset. "::={ cvapSvcStatsEntry 10}
cvapSvcRxReleases OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of RELEASE' messages
received by the media gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 11}cvapSvcRxReleaseCompls OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RELEASE COMPLETE'
messages received by the media gateway from the
PNNI controller since last gateway reset. "::={ cvapSvcStatsEntry 12}
cvapSvcTxRestarts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESTART' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 13}cvapSvcTxRestartAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESTART ACK'
messages sent to the PNNI controller from the
media gateway since last gateway reset. "::={ cvapSvcStatsEntry 14}cvapSvcRxRestarts OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESTART' messages
received by the media gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 15}cvapSvcRxRestartAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESTART ACK' messages
received by the media gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 16}cvapSvcTxResyncStrts OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC START' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 17}cvapSvcTxResyncStrtAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC START ACK'
messages sent to the PNNI controller from the
media gateway since last gateway reset. "::={ cvapSvcStatsEntry 18}cvapSvcRxResyncStrts OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC START' messages
received by the media gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 19}cvapSvcRxResyncStrtAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC START ACK'
messages received by the media gateway from the PNNI
controller since last gateway reset. "::={ cvapSvcStatsEntry 20}cvapSvcTxResyncEnds OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC END' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 21}cvapSvcTxResyncEndAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC END ACK'
messages sent to the PNNI controller from the
media gateway since last gateway reset. "::={ cvapSvcStatsEntry 22}cvapSvcRxResyncEnds OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC END ACK'
messages received by the media gateway from the
PNNI controller since last gateway reset. "::={ cvapSvcStatsEntry 23}cvapSvcRxResyncEndAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'RESYNC END ACK'
messages received by the media gateway from the
PNNI controller since last gateway reset. "::={ cvapSvcStatsEntry 24}cvapSvcTxBulkResyncs OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'BULK RESYNC' messages
sent to the PNNI controller from the media gateway
since last gateway reset. "::={ cvapSvcStatsEntry 25}cvapSvcRxBulkResyncs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of 'BULK RESYNC' messages
received by the gateway from the PNNI controller
since last gateway reset. "::={ cvapSvcStatsEntry 26}cvapSvcCallProcExpiries OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'PROCEED' messages
have been sent from the media gateway and have never received
any response from the PNNI controller. "::={ cvapSvcStatsEntry 27}cvapSvcReleasExpiries OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'RELEASE' messages
have been sent from the media gateway and have never received
any response from the PNNI controller. "::={ cvapSvcStatsEntry 28}cvapSvcConnExpiries OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'CONNECT' messages
have been sent from the media gateway and have never received
any response from the PNNI controller. "::={ cvapSvcStatsEntry 29}cvapSvcConnAckExpiries OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'CONNECT ACK'
messages have been sent from the media gateway and have
never received any response from the PNNI controller. "::={ cvapSvcStatsEntry 30}cvapSvcRestartExpiries OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'RESTART' messages
have been sent from the media gateway and have never received
any response from the PNNI controller. "::={ cvapSvcStatsEntry 31}cvapSvcResyncExpiries OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of call 'RESYNC START'
messages have been sent from the media gateway and have
never received any response from the PNNI controller. "::={ cvapSvcStatsEntry 32}
-- *********************************************************************
-- Conformance
-- *********************************************************************--
-- conformance information
--cvaProfileMIBConformance OBJECTIDENTIFIER::={ ciscoVoiceAalxProfileMIB 2}cvaProfileMIBCompliances OBJECTIDENTIFIER::={ cvaProfileMIBConformance 1}cvaProfileMIBGroups OBJECTIDENTIFIER::={ cvaProfileMIBConformance 2}--
-- Conformance and compliance statements
--cvaProfileMIBCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The Conformance groups."MODULE-- this module
MANDATORY-GROUPS{
cvapCodecConfigGroup
}GROUP cvapSvcConfigGroup
DESCRIPTION"Implementation of this group is mandatory for the
gateway if it supports SVC."GROUP cvapSvcStatsGroup
DESCRIPTION"Implementation of this group is mandatory for the
gateway if it supports SVC statistics."::={ cvaProfileMIBCompliances 1}cvaProfileMIBComplianceRev1 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The Conformance groups."MODULE-- this moduleMANDATORY-GROUPS{
cvapCodecConfigGroupRev1
}GROUP cvapSvcConfigGroup
DESCRIPTION"Implementation of this group is mandatory for the
gateway if it supports SVC."GROUP cvapSvcStatsGroup
DESCRIPTION"Implementation of this group is mandatory for the
gateway if it supports SVC statistics."::={ cvaProfileMIBCompliances 2}--
-- Units of conformance
--cvapCodecConfigGroup OBJECT-GROUPOBJECTS{
cvapCodecNegotiationOption,
cvapCodecConfigPreference,
cvapCodecConfigVoicePacketPeriod,
cvapCodecConfigVbdPacketPeriod,
cvapCodecConfigJitterDelayMode,
cvapCodecConfigJitterMaxDelay,
cvapCodecConfigJitterNomDelay,
cvapCodecConfigJitterMinDelay,
cvapCodecConfigDtmfRelay,
cvapCodecConfigPayloadType
}STATUSdeprecatedDESCRIPTION"This group contains objects related to CODEC
configuration information."::={ cvaProfileMIBGroups 1}cvapSvcConfigGroup OBJECT-GROUPOBJECTS{
cvapSvcAtmQosCellDelay,
cvapSvcAtmQosCtd,
cvapSvcAtmQosClr,
cvapSvcTrfScalingFactor,
cvapSvcAal2CidNumber,
cvapSvcAggTrafficClipping,
cvapSvcAggLinkState,
cvapSvcPartialFillSupported,
cvapSvcMgcpSelectorByteValue,
cvapSvcH248SelectorByteValue,
cvapSvcDelNotifGuardTimer,
cvapSvcMultiCIDPerSvc,
cvapSvcMultiCIDFillTimer,
cvapSvcMultiCIDCACSCR,
cvapSvcMultiCIDCACPCR,
cvapSvcMultiCIDOriginatDelTimer,
cvapSvcMultiCIDTerminatDelTimer,
cvapSvcMultiCIDGlareThreshold
}STATUScurrentDESCRIPTION"This group contains objects related to SVC
configuration information."::={ cvaProfileMIBGroups 2}cvapSvcStatsGroup OBJECT-GROUPOBJECTS{
cvapSvcTxSetups,
cvapSvcRxSetups,
cvapSvcTxCallProcs,
cvapSvcRxCallProcs,
cvapSvcTxConns,
cvapSvcTxConnAcks,
cvapSvcRxConns,
cvapSvcRxConnAcks,
cvapSvcTxReleases,
cvapSvcTxReleaseCompls,
cvapSvcRxReleases,
cvapSvcRxReleaseCompls,
cvapSvcTxRestarts,
cvapSvcTxRestartAcks,
cvapSvcRxRestarts,
cvapSvcRxRestartAcks,
cvapSvcTxResyncStrts,
cvapSvcTxResyncStrtAcks,
cvapSvcRxResyncStrts,
cvapSvcRxResyncStrtAcks,
cvapSvcTxResyncEnds,
cvapSvcTxResyncEndAcks,
cvapSvcRxResyncEnds,
cvapSvcRxResyncEndAcks,
cvapSvcTxBulkResyncs,
cvapSvcRxBulkResyncs,
cvapSvcCallProcExpiries,
cvapSvcReleasExpiries,
cvapSvcConnExpiries,
cvapSvcConnAckExpiries,
cvapSvcRestartExpiries,
cvapSvcResyncExpiries
}STATUScurrentDESCRIPTION"This group contains objects related to SVC statistics."::={ cvaProfileMIBGroups 3}cvapCodecConfigGroupRev1 OBJECT-GROUPOBJECTS{
cvapCodecNegotiationOption,
cvapCodecConfigPreference,
cvapCodecConfigVoicePacketPeriod,
cvapCodecConfigJitterDelayMode,
cvapCodecConfigJitterMaxDelay,
cvapCodecConfigJitterMinDelay,
cvapCodecConfigDtmfRelay,
cvapCodecConfigPayloadType,
cvapCodecConfigNewJtrNomDelay
}
STATUScurrentDESCRIPTION"This group contains objects related to CODEC
configuration information."::={ cvaProfileMIBGroups 4}END